NS0-176 実際試験問題と解答 - 模擬練習 - 受験自信を増やす

Question No : 1
You currently have a FlexPod Datacenter solution, and you are merging with another company. That company's environment currently has a mix of different Cisco servers. You want to add as many of those servers to your FlexPod solution as possible.
In this scenario, which two Cisco servers are supported in a FlexPod environment? (Choose two.)

A.HX240c Edge M5
B.C480 ML M5
C.S3260 M5
D.B200 M5

正解:

Question No : 2
Which two technologies must be deployed for a Cisco Nexus 9000 ACI design? (Choose two.)

A.spine switch
B.VSM
C.APIC
D.LACP

正解:

Question No : 3
Which statement is true for Fibre Channel QoS System Class?

A.One can modify no-drop policy, and non FCoE traffic using natively the same class as FCoE will be remarked to 0
B.One cannot modify no-drop policy, and non FCoE traffic using natively the same class as FCoE will be remarked to 0
C.One can modify no-drop policy, and non FCoE traffic using natively the same class as FCoE will not be remarked
D.One cannot modify no-drop policy, and non FCoE traffic using natively the same class as FCoE will not be remarked

正解:

Question No : 4
What aggregate containing the root volume is created during the Clustered Data ONTAP setup process?

A.8-bit
B.16-bit
C.32-bit
D.64-bit

正解:

Question No : 5
A customer wants to reuse existing networking equipment that was pulled from another data center for a new FlexPod Datacenter solution. They want to know if their switch models are supported.
In this scenario, which two switch models will accomplish this task? (Choose two.)

A.Cisco Catalyst 6504
B.Cisco Catalyst 9300-48P
C.Cisco Nexus 9396PX
D.Cisco MDS 9250i

正解:

Question No : 6
How many ACTIVE SPAN sessions exist on a Fabric Interconnect?

A.1
B.2
C.4
D.8
E.16

正解:

Question No : 7
You are asked to install the Virtual Supervisor Module (VSM) software on a Nexus 1000v switch.
Which two sources would you use to install this software? (Choose two.)

A.OVA file
B.PXE boot
C.ISO image
D.VSC plug-in

正解:

Question No : 8
When trying to configure a Virtual Port Channel (vPC), what might be a cause of the following error when trying to create the vPC domain?
Nexus-5548-B(config)# vpc domain 10
^% Invalid command at '^' marker.Nexus-5548-B(config)#

A.Have not yet turned on the vpc feature using the ‘feature vpc’ command
B.The vPC links have to be configured before the vPC domain can be added
C.The vPC domain has already been configured
D.vPC domain cannot be configured at the global prompt

正解:

Question No : 9
Your customer needs a new Nexus switch that can support at least ten 40GbE ports, and has room for future growth. Your customer would also like the new switch to be Application Centric Infrastructure- ready.
Which switch meets these requirements?

A.Nexus 7004
B.Nexus 5672
C.Nexus 6004
D.Nexus 9504

正解:

Question No : 10
A customer wants a newly deployed UCS C-Series server's fans to run at the minimum speed required to keep the server cool. The customer is also complaining that the server fans are making too much noise.
In this scenario, which type of fan speed should you select under the Power Control Policy of UCSM?

A.Performance
B.Balanced
C.Low Power
D.Max Power

正解:

Question No : 11
Which FlexPod management tool allows you to manage Storage Virtual Machines (SVMs) and replication relationships?

A.OnCommand Performance Manager
B.OnCommand Balance
C.OnCommand System Manager
D.OnCommand Insight

正解:

Question No : 12
A Cisco UCS system is operating in FC End-Host Mode. The fabric Interconnects are uplinked into Nexus 5672UP switches using native FC. The service profiles are unable to boot from SAN using FC.
When executing the show flogi database command on the Nexus switches, only the Fabric Interconnect port WWNs are visible. No service profile WWNs are shown.
What caused this issue?

A.The Nexus switches do not have NPV enabled.
B.The Nexus must be configured for FCoE instead of native Fibre Channel.
C.The Nexus switches do not have NPIV enabled.
D.The zoning on the Nexus switches is incorrect.

正解:

Question No : 13
The NetApp Vistual Storage Console is used to set which three setting categories on ESXi hosts? (Choose three.)

A.MPIO Settings
B.Adapter Settings
C.Logging Settings
D.NFS Settings
E.Security Settings

正解:

Question No : 14
After deploying a FlexPod solution, which tool would you use to validate a successful installation?

A.Hardware Universe
B.Config Advisor
C.System Manager
D.UCS Manager

正解:

Question No : 15
There are 2 chassis tied to a pair of Fabric Interconnects.
First chassis, chassis-1, has 1 link between single IOM and Fabric Module. Second chassis, chassis-4, has 4 links between single IOM and Fabric Module. Chassis discovery policy is set for 2 links.
Which statement is true?

A.Both chassis will be added to UCS Domain utilizing all links. No additional steps needed.
B.Both chassis will be added to UCS Domain utilizing all links only after performing chassis acknowledgment.
C.Chassis-1 will not be added to UCS Domain. Chassis-4 will be added to UCS domain with all 4 links operating and no additional steps needed.
D.Chassis-1 will not be added to UCS Domain. Chassis-4 will be added to UCS domain with all 4 links operating after chassis acknowledgement.

正解:

Network Appliance NS0-176 問題練習