NACE-CIP1-001 実際試験問題と解答 - 模擬練習 - 受験自信を増やす

Question No : 1
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:

A.High Relative Humidity
B.Low Relative Humidity
C.High Surface Temperature
D.Low Surface Temperature

正解:

Question No : 2
The main responsibilities of the inspector are to

A.demonstrate to the contractor how to apply the coating.
B.observe and direct the work of the contractors.
C.direct and perform the work stated in the specification.
D.observe and report the quality of the work performed.

正解:

Question No : 3
ASTM Standards are applicable:

A.In the USA
B.In North America
C.In Asia
D.When specified

正解:

Question No : 4
Excess moisture during holiday testing can cause erroneous indications by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection.
This is often referred to as:

A.telegraphing.
B.monitoring
C.juxtaposing.
D.transitioning.

正解:

Question No : 5
Silicone coatings are typically:

A.Used strictly in immersion service
B.Applied in very thick films
C.Used as a sacrificial primer
D.Applied in very' thin films

正解:

Question No : 6
Inspector's daily reports are used:
Select All That Apply

A.By the contractor to estimate the amount of work done that day
B.To provide continuity between inspectors
C.To aid in arbitration between the contractor and client
D.To help in cases of a coating failure

正解:

Question No : 7
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:

A.Rust Grades A-D
B.Surface Conditions E-G
C.Rust Grades 1-4
D.Surface Condition H

正解:

Question No : 8
Digital hygrometers

A.consist of a bimetallic sensing element protected from wind gusts.
B.are used to measure temperature from a distance.
C.use a thermocouple in contact with the surface to measure temperature
D.determine relative humidity, air temperature, and dew point temperature:

正解:

Question No : 9
Which one of these elements is not necessary for corrosion to occur:

A.Anode
B.Cathode
C.Reference Cell
D.Electrolyte

正解:

Question No : 10
Which of these tests uses a syringe?

A.Sleeve test
B.Potassium ferricyanide
C.Bresle patch
D.Soluble salts meter

正解:

Question No : 11
Conventional spray is a good choice when:

A.High production rates are required
B.High quality finishes are required
C.High transfer efficiency is required
D.High viscosity coatings are being applied

正解:

Question No : 12
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply

A.Failing to determine the base metal reading (BMR)
B.Rotating the dial too fast when taking measurements
C.Taking measurements too far from the edge of a surface
D.Measuring ditty, tacky, or soft films

正解:

Question No : 13
Removal of welds splatter is required:

A.On every job
B.When ISO abrasive blast standards are specified
C.When NACE/SSPC abrasive blast standards are specified
D.When specifically identified in the owner's specification

正解:

Question No : 14
In a non-convertible coating the role of the primary solvent is to:

A.To make the coating flow out better
B.To dissolve the resin
C.To promote faster cure
D.To control the evaporation rate

正解:

Question No : 15
It is good practice for the NACE Inspector to have instrument calibration certificates available:

A.At all times
B.In the office only
C.In the field only
D.Only if the specification requires it

正解:

NACE NACE-CIP1-001 問題練習