D-PE-OE-01 実際試験問題と解答 - 模擬練習 - 受験自信を増やす

Question No : 1
A technician is deploying a server.
What should they do once the server is fully configured and deployed?

A.Switch on write-protect for the vFlash SD card
B.Back up the server profile and reset the iDRAC to Default Settings
C.Back up the server profile and configure the Parts Replacement feature
D.Change the iDRAC secure password based on the users’ company policies

正解:

Question No : 2
A new server with default iDRAC network configurations is plugged into a segregated management network configured for 10.0.0.x/24. The technician cannot connect to the iDRAC.
How can the on-site technician configure the iDRAC for network access?

A.Change iDRAC network settings from a workstation on the management network
B.Perform an AC power cycle to reset the iDRAC
C.Modify the iDRAC settings using the iDRAC Direct feature
D.Configure a DHCP reservation for the iDRAC MAC address

正解:

Question No : 3
An engineer needs to install an additional PSU on an existing, single PSU Dell EMC PowerEdge R740. They complete the initial installation and cabling procedures. They connect an AC cable and the power distribution unit produces normal AC output. The engineer checks power management and sees that the new PSU is in the Failed state.
What task should be completed to troubleshoot this issue?

A.Confirm the System Input Power CAP is not set to Low
B.Set the PSU AC redundancy to 1+1
C.Set the PSU AC redundancy to 1+0
D.Verify the new PSU is the same type and wattage rating

正解:

Question No : 4
A system administrator is trying to connect with a mobile device to a Dell PowerEdge 16G server using Quick Sync 2. They failed to make a connection.
What is the reason for the failure?

A.Bluetooth is disabled on the mobile device.
B.NFC is disabled on the mobile device.
C.There is no iDRAC IP address configured.
D.The mobile device is using iO

正解:

Question No : 5
On a PowerEdge R640 server, the System Lockdown mode has been enabled. Certain features are no longer available in the System BIOS utility or IDRAC GUI.
Which other feature is no longer available?

A.OMSA
B.Lifecycle Controller
C.iSM
D.Booting to a 32-bit OS

正解:

Question No : 6
Which characteristic of system management enables a company to reduce costs?

A.Integration with third-party tools
B.Multi-tenancy support
C.Rich management interface
D.Automation of routine tasks

正解:

Question No : 7
A technician needs to initially configure a server from a bare metal condition in the following areas:
- Processor settings
- Disk configuration
- iDRAC network settings
The technician can only reboot once to achieve these tasks.
Where should the technician configure these settings? (Choose three.)

A.PXE Settings
B.System BIOS
C.PERC Configuration Utility
D.iDRAC Settings
E.Device Settings

正解:

Question No : 8
A technician is tasked to perform a RAID Level Migration (RLM) of a RAID 5 array to a RAID 6 array. They back up data and look in iDRAC Storage and find that the current RAID 5 array is sliced into two virtual disks.
What should the technician do to achieve the desired RAID level?

A.Reboot and press Ctrl-R to complete RAID migration
B.Use iDRAC GUI under Storage Configuration to delete the arrays and recreate the new RAID 6 array
C.Open the OpenManage Enterprise GUI, delete the arrays, and recreate the new RAID 6 array
D.Use SupportAssist Enterprise to complete RAID migration

正解:

Question No : 9
A user has a number of PowerEdge servers and installs OME on a remote system to monitor the servers. When attempting to discover one of the servers, the discovery process is unsuccessful. The user accesses the Troubleshooting tool to establish that the communication pathway is correct.
After entering the server iDRAC IP address, which network protocol should be selected to communicate with the iDRAC?

A.SNMP
B.IPMI
C.In-Band
D.WS-MAN

正解:

Question No : 10
From PERC8 to PERC9, the maximum number of individual drives upon which a virtual disk can be created changed.
How did this value change?

A.8 to 32
B.16 to 64
C.16 to 32
D.8 to 16

正解:

Question No : 11
A technician has the ISO image of an OS that they need to install on a server in a remote location. They are already logged into the iDRAC.
How should the technician install the OS?

A.Click Launch under the Virtual Console Preview, Select Next Boot, and choose Virtual CD/DVD/ISO
B.Click Launch under the Virtual Console Preview and then connect to Virtual Media
C.Click Launch under the Virtual Console Preview, reboot the server into F10, and start the Lifecycle Controller OS Deployment wizard
D.Click on Update and Rollback under Quick Launch Tasks

正解:

Question No : 12
A technician resets the iDRAC but when they attempt to log back in to the iDRAC is offline.
Why is the iDRAC offline?

A.DRAC has reset to the default IP address of 192.168.0.120
B.Technician must use iDRAC Direct to enable the iDRAC network
C.iDRAC is still in the reset process
D.Technician must move the iDRAC network cable back to the iDRAC dedicated NIC

正解:

Question No : 13
A company's servers were ordered with iDRAC Enterprise with vFlash. The server profile was backed up after the first boot. Changes have been made to the server BIOS settings and firmware versions, which have resulted in many performance issues.
What is the most efficient way for the technician to address the performance issues?

A.Upload the approved corporate firmware versions from the file share
B.Restore system profile using the iDRAC or Lifecycle Controller
C.Run the racadm racresetcfg command to reset all server settings
D.Reboot the server to F10 and perform System Repurpose/Retire

正解:

Question No : 14
What does OBPAR allow on a PowerEdge MX750c?

A.Run a compute sled with memory overclocking.
B.Boot a compute sled with only one CP
C.Run a compute sled with maximum performance.
D.Boot a compute sled with reduced frequency.

正解:

Question No : 15
Refer to the exhibit.

A system administrator wants to monitor information about the system using their smartphone and a Bluetooth connection. LED labeled 3 on the control panel is solid white.
What does the LED indicate?

A.The system is powered on.
B.Quick SYNC 2 is ready to communicate.
C.OMM is transferring data.
D.The system is in failsafe mode.

正解:

DELL EMC D-PE-OE-01 問題練習