C_IBP_2305 実際試験問題と解答 - 模擬練習 - 受験自信を増やす

Question No : 1
Which sets of chart types are provided within the Analytics Advanced application? Note: There are 3 correct answers to this question.

A.Comparison Chart Types
B.Seasonal Chart Types
C.Trend Chart Types
D.Geographic Chart Types
E.Simulation Chart Types

正解:

Question No : 2
You need to create time periods for the time profile in a planning area.
What should you be aware of when running the Create Time Periods application job?

A.The assigned Planning Area must be active.
B.This application job can be run for multiple time profiles at once.
C.In the Parameter Section of the application job, choose the Time Profile ID and Planning Area.
D.A time profile has to be activated so that the application job can proceed.

正解:

Question No : 3
Which of the following data inputs, when increased, will always cause an increase in the safety stock outputs when the Global (multi-stage) Inventory Optimization operator is run? Note: There are 2 correct answers to this question.

A.Holding Cost Percentage
B.Minimum Lot Size
C.Target Service Level
D.Transportation Lead Time Error CV

正解:

Question No : 4
You are reviewing the master data types that are often used for supply and inventory planning.
Which master data types are compound master data types? Note: There are 2 correct answers to this
question.

A.SOURCELOCATION
B.SOURCECUSTGROUP
C.SOURCECUSTOMER
D.SOURCEPRODUCTION

正解:

Question No : 5
Which SAP IBP planning operator can be run to delete planning objects in a certain version?

A.Purge Key Figure Data
B.Purge Key Figure Data Outside Planning Area Planning Horizon
C.Purge Non-Confirming Data
D.Purge Master Data

正解:

Question No : 6
Which are the mandatory preconditions for an attribute that can be used for saving the segmentation results? Note: There are 2 correct answers to this question.

A.The Business Meaning of the attribute has been specified.
B.The attribute should be a non-key attribute of the master data type.
C.The attribute belongs to a simple or compound master data type.
D.The attribute should be assigned to all planning levels.

正解:

Question No : 7
For your project, you create a new planning area and consider how to create analytics and alerts for it.
How can you create these objects?

A.Use the option for copying analytics and alerts into the new planning area from the existing custom planning area.
B.Create analytics and alerts in the new planning area from scratch using the Intelligent Visibility application.
C.Use the option for copying analytics and alerts when creating a new planning area from the sample SAPIBP1.
D.Merge analytics and alerts into a new planning area from any sample planning area.

正解:

Question No : 8
What is a prerequisite for modeling outsourced manufacturers with production capacity using the Supply Optimizer?

A.Use production lead times and offsets to manage components at the outsourced manufacturing location
B.Ensure that the outsourced manufacturing locations have a separate subnetwork
C.Model target inventory and stocks at the outsourced manufacturing location
D.Model relative production costs across internal locations and outsourced manufacturing locations

正解:

Question No : 9
How many different time levels can be selected within one planning view?

A.Only base time levels of the planning area
B.All time levels available in the time profile
C.All time levels available in the time profile, restricted by global configuration parameter
D.Only time levels from the base planning level of selected key figures

正解:

Question No : 10
Which type of Master Data will be represented by the Master Data Type LOCATIONFR?

A.Virtual Master Data Type
B.Reference Master Data Type
C.Compound Master Data Type
D.External Master Data Type

正解:

Question No : 11
Which of the following are capabilities of the Manage Forecast Error Calculations - Inventory Optimization app? Note: There are 2 correct answers to this question.

A.Adjust for forecast bias in Forecast Error CV calculations
B.Propagate forecast error to upstream locations in a supply chain network
C.Adjust Safety Stock Recommendations based on forecast error CV input
D.Identifiy intermittent demand for Forecast Error CV calculations

正解:

Question No : 12
You need to use your resource cost effectively with a certain minimum use, even if it means producing more than demand.
Which solutions would apply to this scenario? Note: There are 2 correct answers to this question.

A.Capacity leveling will be possible for production and storage resources.
B.Balance can be achieved between excessive prebuild and minimum use by incorporating violation costs.
C.Excess stock can be generated and will need to be staged in an overflow warehouse.
D.Minimum capacity utilization will result in pull production occurring.

正解:

Question No : 13
You need to define a new logic for a key figure to drive values from the PERPRODCUSTREGION level to the PERPRODCUST level.
Which of the following configuration options are possible for this process? Note: There are 2 correct answers to this question.

A.Splitting the values from aggregated to detailed level, based on the time profile attribute
B.Splitting the values from aggregated to detailed level, based on a stored split-factor key figure
C.Splitting the values from aggregated to detailed level using multiplication by the proportions
D.Splitting the values from detailed to aggregated level by using a copy operator

正解:

Question No : 14
You created a key figure and want to add calculations.
Which of the following rules do you consider? Note: There are 2 correct answers to this question.

A.Aggregation calculations using SUM or MAX functions must be based on a higher aggregation level.
B.The calculation chain for a key figure must always result in a calculated key figure.
C.Key figures can be calculated across different planning levels.
D.All key figure calculations have calculation inputs, which can be marked as stored or calculated.

正解:

Question No : 15
Model configuration allows the attributes of a master data type to be assigned as key figures.
Which features are relevant for this type of object?

A.This type of key figure is not usually stored and it cannot be set to editable.
B.This object is not exposed to the user in planning views or modeling.
C.This object contains user-defined criteria that monitor the running of business plans.
D.This object provides a single value for a unique planning combination.

正解:

SAP C_IBP_2305 問題練習