API API-1184 問題練習

Question No : 1
What is an “appurtenance” in the context of API RP 1110?

• A.A type of anomaly in the pipeline material
• B.A component attached to the pipeline
• C.A type of pipeline operating condition
• D.A pressure testing tool

答えを確認する

正解:

Question No : 2
Which of the following is NOT covered by API RP 1110?

• A.Line pipe
• B.Control piping
• C.Valves
• D.Breakout tanks

答えを確認する

正解:

Question No : 3
What does “RP” stand for in API RP 1110?

• A.Recommended Procedure
• B.Regulatory Practice
• C.Recommended Practice
• D.Regulatory Procedure

答えを確認する

正解:

Question No : 4
Which of the following is NOT a guiding principle of API RP 1110?

• A.Providing a consistent means of preparing and assessing pressure test results
• B.Defining specific engineering solutions
• C.Ensuring personnel safety during pressure tests
• D.Accommodating present and future pipeline technologies

答えを確認する

正解:

Question No : 5
What does API RP 1110 provide guidelines for?

• A.Pressure testing water pipelines
• B.Pressure testing steel pipelines
• C.Pressure testing pipelines for natural gas only
• D.Pressure testing pipelines for liquids only

答えを確認する

正解:

Question No : 6
What is the term for a weld made to repair a defect found by visual testing?

• A.Corrective weld
• B.Secondary weld
• C.Repair weld
• D.Adaptive weld

答えを確認する

正解:

Question No : 7
What does “EU” represent in API 1104?

• A.External Undercutting
• B.End User
• C.Erosion Undercutting
• D.Elevated Unction

答えを確認する

正解:

Question No : 8
What is the significance of “stacked defects” in welding according to API 1104?

• A.Defects piled on top of each other
• B.A type of welding defect
• C.Weld discontinuities aligned in a specific direction
• D.Defects that have been repaired

答えを確認する

正解:

Question No : 9
Which type of welding involves mechanically controlling parameters and torch guidance?

• A.Position welding
• B.Mechanized welding
• C.Waveform-controlled welding
• D.Semiautomatic welding

答えを確認する

正解:

Question No : 10
Which organization provides the “ISO 19232-15” standard referenced in API 1104?

• A.American Welding Society (AWS)
• B.International Organization for Standardization (ISO)
• C.NACE International
• D.British Standards Institution (BSI)

答えを確認する

正解:

Question No : 11
What does “HVL” stand for in API 1104?

• A.High Voltage Level
• B.Heat Variability Level
• C.Half-Value Layer
• D.High Velocity Limit

答えを確認する

正解:

Question No : 12
Which term refers to an indication with its greatest dimension in the weld length direction?

• A.Volumetric indication
• B.Linear indication
• C.Transverse indication
• D.Radial indication

答えを確認する

正解:

Question No : 13
What is the main purpose of “UT qualification” according to API 1104?

• A.To test the ultrasonic equipment
• B.To evaluate the performance of welders
• C.To ensure proper equipment maintenance
• D.To evaluate the ultrasonic testing system’s accuracy

答えを確認する

正解:

Question No : 14
Which term refers to welding in which the pipe is rotated while the weld metal is being deposited?

• A.Position welding
• B.Roll welding
• C.Mechanized welding
• D.Arc welding

答えを確認する

正解:

Question No : 15
What is the purpose of “visual examination or testing” according to API 1104?

• A.To evaluate the weld’s mechanical properties
• B.To determine the cost of the welding process
• C.To detect surface discontinuities and evaluate weld acceptability
• D.To measure the heat input during welding

答えを確認する

正解: